Celestron CGE925 Bedienerhandbuch PDF herunterladen (Seite 27)

by inputting a value which quickly rewinds the motors just enough to eliminate the play between gears. The amount of

compensation needed depends on the slewing rate selected; the slower the slewing rate the longer it will take for the star to

appear to move in the eyepiece. There are two values for each axis, positive and negative:

Positive is the amount of compensation applied when you press the button, in order to get the gears moving quickly without a

long pause.

Negative is the amount of compensation applied when you release the button, winding the motors back in the other direction

to resume tracking.

Normally both values should be the same. You will need to experiment with different values (from 0-99); a value between 20

and 50 is usually best for most visual observing, whereas a higher value may be necessary for photographic guiding.

To set the anti-backlash value, scroll down to the

anti-backlash option and press ENTER. While viewing an object in the

eyepiece, observe the responsiveness of each of the four arrow buttons. Note which directions you see a pause in the star

movement after the button has been pressed. Working one axis at a time, adjust the backlash settings high enough to cause

immediate movement without resulting in a pronounced jump when pressing or releasing the button. Now, enter the same

values for both positive and negative directions. If you notice a jump when releasing the button, but setting the values lower

results in a pause when pressing the button, go with the higher value for positive, but use a lower value for negative. The

telescope will remember these values and use them each time it is turned on until they are changed.

Filter Limits – When an alignment is complete, the telescope automatically knows which celestial objects are above the

horizon. As a result, when scrolling through the database lists (or selecting the Tour function), the hand control will display

only those objects that are known to be above the horizon when you are observing. You can customize the object database by

selecting altitude limits that are appropriate for your location and situation. For example, if you are observing from a

mountainous location where the horizon is partially obscured, you can set your minimum altitude limit to read +20º. This will

make sure that the hand control only displays objects that are higher in altitude than 20º.

If you want to explore the entire object database, set the maximum altitude limit to 90º and the minimum limit to –90º.

This will display every object in the database lists regardless of whether it is visible in the sky from your location.

Direction Buttons –The direction a star appears to move in the eyepiece changes depending on which side of the Meridian

the telescope tube is on. This can create confusion especially when guiding on a star when doing astrophotography. To

compensate for this, the direction of the drive control keys can be changed. To reverse the button logic of the hand control,

press the MENU button and select

Direction Buttons from the Utilities menu. Use the Up/Down arrow keys (10) to select

either the azimuth (right ascension) or altitude (declination) button direction and press ENTER. Select either positive or

negative for both axes and press ENTER to save. Setting the azimuth button direction to positive will move the telescope in

the same direction that the telescope tracks (i.e. towards the west). Setting the altitude buttons to positive will move the

telescope counterclockwise along the DEC axis.

Goto Approach - lets the user define the direction that the telescope will approach when slewing to an object. This allows

the user the ability to minimize the effects of backlash when slewing from object to object. Just like with

Direction Buttons,

setting

GoTo Approach to positive will make the telescope approach an object from the same direction as tracking (west) for

azimuth and counterclockwise in declination. Declination Goto approach will only apply while the telescope tube is on one

side of the Meridian. Once the tube passes over to the other side of the Meridian, the Goto approach will need to be reversed.

To change the Goto approach direction, simply choose

Goto Approach from the Scope Setup menu, select either Altitude or

Azimuth approach, choose positive or negative and press ENTER.

In order to minimize the affect of gear backlash on pointing accuracy, the settings for Button Direction should ideally

match the settings for GoTo Approach. By default, using the up and right direction buttons to center alignment stars

will automatically eliminate much of the backlash in the gears. If you change the Goto approach of your telescope it

is not necessary to change the Button Direction as well. Simply take notice of the direction the telescope moves when

completing its final goto approach. If the telescope approaches its alignment star from the west (negative azimuth)

and clockwise (negative altitude) then make sure that the buttons used to center the alignment stars also move the

telescope in the same directions.

Observing

Tip!

Helpful

Hint!

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 71 72

Kommentare zu diesen Handbüchern

Keine Kommentare

Celestron CGE925 Bedienerhandbuch Seite 27

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Teleskope Celestron CGE925