Celestron CGE925 Bedienerhandbuch Seite 7
- Seite / 72
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
7
3. Slide the center portion of the tripod leg away from the tripod head until it is at the desired height.
4. Tighten the levers on each leg clamp to hold the legs in place.
5. Once that it is fully assembled, rotate the tripod so that one of the legs is pointing roughly towards north.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
A
A
c
c
c
c
e
e
s
s
s
s
o
o
r
r
y
y
T
T
r
r
a
a
y
y
1. Slide the accessory tray over the central rod so that the three cup indents are pushing against the inside of the tripod legs.
2. Thread the accessory tray knob on to the central rod and tighten.
To transport your tripod, remove the knob and lower the accessory tray far enough to rotate it until the three recesses line up
with each leg. Collapse the legs so that each leg falls into one of the recesses. Secure the legs together with the nylon strap
attached to the tripod leg.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
E
E
l
l
e
e
c
c
t
t
r
r
o
o
n
n
i
i
c
c
s
s
P
P
i
i
e
e
r
r
Before the equatorial mount head can be installed, the electronics pier must be attached to the tripod. To attach the pier:
1. Position the electronics pier so that the electronics
module is right side up (with the printing readable).
2. Place the bottom of the pier over the tripod head.
3. Rotate the column until the three holes line up with
the threaded holes on the side of the tripod head. The
pier should be positioned so that the motor ports
(labeled RA and DEC) are on the east side of the
mount. (see figure 2-4)
4. Insert the three 3/8-16 Allen head screws and washers
provided through the holes in the electronics pier and
into the tripod head.
5. Tighten the screws to hold the column securely in
place.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
E
E
q
q
u
u
a
a
t
t
o
o
r
r
i
i
a
a
l
l
M
M
o
o
u
u
n
n
t
t
After the tripod is set up, you are ready to attach the equatorial
mount. The equatorial mount is the platform to which the
telescope attaches and allows you to move the telescope in
right ascension and declination. To attach the equatorial mount
to the tripod:
1. Insert the base of the equatorial mount into the top of
the electronics pier.
2. Rotate the equatorial mount on the electronics pier
until the holes in the mount line up with those in the
pier and the DEC opening (where the counterweight shaft will go) is positioned directly over the north tripod leg.
3. Insert the three remaining 3/8-16 screws and washers provided through the holes in the electronics pier and into the
equatorial mount.
4. Tighten the screws to hold the equatorial mount in place.
North Leg
Electronics Pier
Tripod Head
Equatorial
Mount
Figure 2-2
- Warning 4
- Figure 2.2 – CGE Pro 5
- North Leg 7
- Electronics Pier 7
- Tripod Head 7
- Equatorial 7
- Figure 2 10
- Figure – 2-7 10
- Alignment Screws 12
- Quick release 12
- Figure 2-13 13
- Figure 2-14 13
- Figure 2-16 15
- Figure 3 17
- The Hand Control 17
- Hand Control Operation 18
- Updating Your Location 19
- East/West (E/W) Filtering 20
- Selecting an Object 22
- Slewing to an Object 23
- Finding Planets 23
- Tour Mode 23
- Constellation Tour 23
- Direction Buttons 23
- Rate Button 24
- Sidereal 25
- Solar 25
- Precise GoTo 26
- Scope Setup Features 26
- Observing 27
- Helpful 27
- Utility Features 29
- - If using your telescope 31
- - Allows you to turn off 31
- ALIGNMENT 32
- Image Orientation 33
- Focusing 34
- Calculating Magnification 34
- Determining Field of View 34
- General Observing Hints 35
- Motion of the Stars 37
- Polar Aligning the Mount 38
- Observing the Moon 41
- Lunar Observing Hints 41
- Observing the Planets 41
- Observing the Sun 41
- Figure 6-1 43
- Eyepiece Projection 45
- Table 7-2 46
- Terrestrial Photography 49
- Metering 49
- Reducing Vibration 49
- CCD Imaging 49
- Auto Guiding 50
- Collimation 51
- Additional RS232 Commands 62
- CELESTRON TWO YEAR WARRANTY 71
Verwandte Produkte und Handbücher für Teleskope Celestron CGE925
Teleskope Celestron 93515 Bedienerhandbuch
(19 Seiten)
(19 Seiten)
Teleskope Celestron 93517 Bedienerhandbuch
(62 Seiten)
(62 Seiten)
Teleskope Celestron 11007 Betriebsanweisung
(75 Seiten)
(75 Seiten)
(2 Seiten)
(1 Seiten)
(1 Seiten)
Teleskope Celestron 21065 Bedienungsanleitung
(56 Seiten)
(56 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.787 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern